SILENT KNIGHT 4821 Manuel d'installation Page 62
- Page / 154
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Model 4821/4820 Control/Communicator Installation Manual
4-18 150964
4.14 Touchpad Installation
This section describes installation of a touchpad for basic system operation. For information
about how to install 4860C touchpads as input zones, see Section 4.15.5.
4.14.1 Touchpad Specifications
• When installed for use as an access control system the touchpad must be located inside the
protected premises.
• 24 touchpads/card readers maximum per system.
• All touchpads require four wires to operate.
• Maximum distance from the control panel depends on the number of devices attached to
the SBUS. See Section 4.13.3 for complete information.
• Maximum current draw: 90 mA
• Standby current draw: 48 mA
• Maximum allowed voltage drop for a touchpad wire run: 2V
• For best system performance, connect most touchpads to the same SBUS, either SBUS1
or SBUS2. (Connect all other SBUS devices to the SBUS that is not used by touchpads.)
4.14.2 Mounting Touchpads
1. Separate the top section from the rear mounting plate. Do this by inserting a small flat-
blade screwdriver into the slot located on the bottom edge of the frame. (See Figure 4-11.)
Push in, then lift up the top section.
Figure 4-11 Mounting Plate Slot location.
2. Secure the mounting plate to the wall using the screw (#6 or #8) appropriate for the type of
wall material.
3. The mounting plate should be oriented so that the protruding tab and the three posts are
towards the bottom. Pull the wires through the hole in the rear mounting plate.
- Contents 1
- Section 3 2
- Section 4 2
- Section 5 4
- Section 6 5
- Troubleshooting 6
- Section 1 7
- Introduction 7
- 1.1.1 Compatible Modules 8
- 1-4 150961 10
- 1.2 How to Use this Manual 11
- 1.4 Agency Requirements 12
- 1.4.3 UL Requirements 13
- 1.4.3.2 Grade A Mercantile 14
- 1.4.3.4 Access Control UL-294 15
- 1-10 150961 16
- Section 2 17
- Quick Start 17
- 2-2 150962 18
- 2.2 Sending Data to the Panel 19
- 2.4 Installation Records 20
- 2.4.1.1 Zone Record 22
- 4815 Expander Loop2 25
- 2-10 150962 26
- 3-2 150963 28
- 150963 3-3 29
- 3-4 150963 30
- 3.2.2 Mounting 31
- 3-6 150963 32
- 150963 3-7 33
- 3-8 150963 34
- 150963 3-9 35
- 3.4 Access Control Operation 36
- 3.4.2 End-User Operation 37
- 3.4.4 Viewing Door Status 38
- 3.4.5 Anti-Passback Feature 39
- 3-14 150963 40
- 150963 3-15 41
- 3-16 150963 42
- 150963 3-17 43
- 3-18 150963 44
- 4.3 Board Layout 46
- 150964 4-3 47
- 4.5 Power Limiting Circuits 48
- 4.6 Power Switch 49
- 4.8 Wire Routing 50
- 4.9 Current Draw Worksheets 51
- 4-8 150964 52
- 150964 4-9 53
- 4-10 150964 54
- 150964 4-11 55
- 4.10 AC Power Transformer 56
- 150964 4-13 57
- 4-14 150964 58
- 4.13 SBUS 59
- 4-16 150964 60
- Max. Distance = 500V 61
- 4.14 Touchpad Installation 62
- 4.14.3 Wiring Touchpads 63
- 4.15 Zone Installation 64
- 4.15.3 Zone Configuration 65
- 4-22 150964 66
- 150964 4-23 67
- 4-24 150964 68
- 150964 4-25 69
- 4.16.1.1 Smoke Reset Cycle 70
- 150964 4-27 71
- 4.17 Speaker Wiring 72
- 4.18 Bell Wiring 73
- 4.18.2 Commercial Bell Wiring 74
- 4.19 4884 Bell Module wiring 75
- 4-32 150964 76
- 150964 4-33 77
- 4.21 Built-in Relay 78
- 4.22 DACT Compliant Wiring 79
- Alarm Relay Trouble Relay 80
- 150964 4-37 81
- 4-38 150964 82
- 5-2 150965 84
- 5.2 Touchpad Models 86
- 6LOHQW.QL 87
- 5.3.2 Normal Display Messages 88
- 5.3.3 System Status Messages 88
- 5.4 Touchpad Buttons 89
- 5-8 150965 90
- 5.6 Interactive Menu Overview 91
- 5.7 System Operation Summary 92
- 5-12 150965 94
- 5-14 150965 96
- 5.9 System Test Descriptions 98
- 5-18 150965 100
- System Operation 101
- 5-20 150965 102
- MUTE-Exit Menu 103
- [Installer’s Code] 104
- 6.2.2.1 1-Install Device 105
- 6.2.2.2 2-Edit System Options 105
- 6.2.2.3 3-Edit Partition 106
- 6.2.2.4 4-Edit Ph. Lines 106
- 6.2.2.5 5-Reprt Accounts 107
- 6.2.2.6 6-Print Accounts 107
- 6.2.2.7 7-Edit Profiles 108
- Programming 109
- 6-8 150966 110
- 6.2.2.9 8-Edit Schedules 111
- 6.2.2.10 9-Delete Options 112
- 6.3 Programmable Options 113
- 6-12 150966 114
- 6.3.1.2 Dialer Screen 116
- 6.3.1.3 Devices Screen 117
- 6-16 150966 118
- 6-18 150966 120
- 6-20 150966 122
- 6-22 150966 124
- 6.3.2.3 Zones Screen 125
- 6-24 150966 126
- 6-26 150966 128
- 6-28 150966 130
- 6.3.2.5 Areas Screen 132
- 6.3.3 Time Schedules Screen 133
- 6.3.4 Universal Schedules 134
- 6.3.5 User Profiles Screen 135
- 6.3.6 Users Screen 136
- Section 7 137
- Reportin 137
- 7.2 SIA Event Codes 138
- Reporting 139
- 7-4 150967 140
- 3 = Restore event 142
- 7-8 150967 144
- Open-Close 146
- 7-12 150967 148
- Alarm Restore 149
- Alarm Rese 149
- Door Access 149
- Exception OPCL 150
- Trouble OPCL 150
- Door Access Denied 151
- Door Exit 151
- Door Left Open 151
- 7-16 150967 152
- Section 8 153
- Troubleshootin 153
- 8-2 150968 154
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité SILENT KNIGHT 4821
(186 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels